SPOT DETECTOR IP212-116 TRION

The detector is designed to detect fires accompanied by smoke or low-concentration combustion products in enclosed spaces of various buildings and structures, and to send a "Fire" alert to the control panel. The detector can be installed in explosion-hazardous areas of indoor and outdoor installations of class 0 and lower, depending on the design.

Review of the TRION VZ detector

Review of the TRION MK detector

Name	IP 212-116.2 Trion MK	IP 212-116 Trion VZ
Explosion protection marking	1Ex d ia IIB T6 Gb	0Ex ia IIB T6 Ga
Marking of spark protection parameters		LI: 10μH, CI: 1000pF,
Marking of spark protection parameters		Ui: 30B, Ii: 20mA, PI: 0.3W
Degree of protection of the shell	IP67/IP31	IP67/IP31
Operating temperature range	-40°С .. +75°С	-40°С .. +75°С
Supply voltage range	10V .. 30V	10V .. 30V
Current consumption:
in standby mode, no more	90 µA	90 µA
in alarm mode, no more	20 mA	100 mA
Detector sensitivity	0.05 dB/m .. 0.2 dB/m	0.05 dB/m .. 0.2 dB/m
Detector response time, no more than	5 sec.	5 sec.
Body material	Aluminum alloy, Stainless steel	Impact-resistant polyamide

Table for selecting the ratings of additional resistors

Type of control panel	Connection parameters
Type of control panel	Parallel connection (for short circuit)	Sequential connection (on opening)
LB-07	Rд must provide current consumption >15 mA,	Rd = 11 kOhm, Rok = 2 kOhm, VDok = KD522.
LB-07	Rok = 2 kOhm, VDok = KD522.	Rd = 11 kOhm, Rok = 2 kOhm, VDok = KD522.
Beam	Rd = 2.4 kOhm, Rok = 2.4 kOhm, VDok = KD521A.	Rd = 2.2 kOhm, Rok = 2.4 kOhm, VDok = KD521A.
PPK-2	Rd = 1.2 kOhm, Rok = 3.6 kOhm, VDok = KD521A.	Rd = 10.0 kOhm, Rok = 3.6 kOhm, VDok = KD521A.
Bolide	Rд = 1.5 kOhm (3.0 kOhm - to determine double operation),	Rд = 8.2 kOhm (4.7 kOhm - to determine double operation),
Bolide	Rок = 4.7 kOhm, VDок do not install	Rок = 4.7 kOhm, VDок do not install
Yakhont-16i	Rд = 1.8 kOhm (4.0 kOhm - to determine double operation),	Not applicable
Yakhont-16i	Rок = 8.2 kOhm, VDок do not install	Not applicable
VERS	Rд = 820 Ohm (1.8 kOhm - to determine double operation),	Rд = 10 kOhm (4.7 kOhm - to determine double operation),
VERS	Rок = 7.5 kOhm, VDок do not install	Rок = 7.5 kOhm. Do not install VDок.

AM – indicates the presence of a product modification with an address mark.

The IP 212 Trion is a maximum-range detector and can be used in short-circuit alarm loops (parallel connection). The "Fire" alarm is provided by a sudden decrease in the detector's resistance.
The detector has a built-in optical indication of operation.
A replaceable current-limiting resistor is used for configuration of the fire alarm control panel type. The detector's trigger signal remains active after exposure to combustion products ceases. The detector can be returned to standby mode from the control panel.
The IP 212 Trion VZ detector is supplied with two cable entries, which allow the detector to be installed in an alarm circuit with a round cable with a diameter of 6-10 mm.
The IP 212 Trion MK detector is supplied with cable entries of various designs:
- for open installation of connected cable with a diameter of 6-12 mm (index in the designation - K );
- for laying the connecting cable in a G1/2 pipe ( TG-1/2 );
- for laying the connecting cable in a G3/4 ( TG-3/4 ) pipe;
- for connecting armoured cable with a diameter of 6-12 mm ( B).

SPOT DETECTOR IP212-116 TRION

Review of the TRION VZ detector

Review of the TRION MK detector

THIS SITE USES COOKIES