SMD-TLT Logo

Products

SMOKE POINT DETECTOR IP212 TRION OP-N

SMOKE POINT DETECTOR IP212 TRION OP-N

Select the parameters
ДЫМОВОЙ ТОЧЕЧНЫЙ ИЗВЕЩАТЕЛЬ ИП212 ТРИОН ОП-Н
ДЫМОВОЙ ТОЧЕЧНЫЙ ИЗВЕЩАТЕЛЬ ИП212 ТРИОН ОП-Н ДЫМОВОЙ ТОЧЕЧНЫЙ ИЗВЕЩАТЕЛЬ ИП212 ТРИОН ОП-Н ДЫМОВОЙ ТОЧЕЧНЫЙ ИЗВЕЩАТЕЛЬ ИП212 ТРИОН ОП-Н ДЫМОВОЙ ТОЧЕЧНЫЙ ИЗВЕЩАТЕЛЬ ИП212 ТРИОН ОП-Н
Выгоднее на
SMOKE POINT DETECTOR IP212 TRION OP-N
Equipment
  • Request a price from the manager
You choosed:
  • Equipment

The detector is designed to detect fires accompanied by the appearance of smoke or low-concentration combustion products in enclosed spaces of various buildings and structures by detecting optical radiation reflected from smoke particles and sending a “Fire” notice to the control panel. Alarm notification "Fire" is provided by an abrupt decrease in the resistance of the detector when connected in parallel to the fire alarm loop. The detector complies with TR EAEU 043/2017, GOST R 53325-2012.

The detector is designed for operation at ambient temperature from minus 40°С to plus 75°С, climatic version UHL2 according to GOST 15150-69. The degree of protection of the enclosure is IP67/IP31 according to GOST 14254. The degree of protection IP31 refers to a smoke detector that cannot be placed inside a flameproof enclosure. Placement category 2 according to GOST 15150-69.

Case material - either corrosion-resistant stainless steel 12X18H10T.

According to the method of protecting a person from electric shock, the detector corresponds to class III according to GOST IEC 61140-2012.

The detectors comply with the norms and requirements of electromagnetic compatibility in accordance with GOST R 53325-2012 with a degree of test severity 2. Radio interference from the detector does not exceed the standards established by GOST 30805.22-2013 (CISPR 22:2006) for class B equipment.

IP 212-116.2 Trion MK-OP - N is a maximum action detector and can be used in short circuit alarm loops (parallel connection).

The detector can be manufactured with address expander "S2000-AP1 version 2" manufactured by OOO "Bolid". The address version of the detector is used with the two-wire communication line controller "S2000-KDL" or "S2000-KDL-2I" as part of the integrated security system "Orion". https://bolid.ru/

The detector is equipped with two cable glands of the KV TU 27.33.13-359-81888935-2019 series. Connecting thread of cable glands M20x1.5. Cable glands allow you to enter and exit round cables of various diameters:

  • for open laying of the attached cable (index in the designation - K);
  • for laying the attached cable in a pipe with an internal or external thread G1 / 2 or M20x1.5 (TV1 / 2, TH1 / 2, TV20, TH20);
  • for connecting an armored cable with a double seal (B);
  • for connecting a cable in a metal hose RZTSH-10mm, RZTSKh-12mm, RZTSKh-15mm or RZTSKh-20mm (KM10, KM12, KM15, KM20).
Degree of protection of the shellIP67/IP31
Operating temperature range-40°С .. +75°С
Supply voltage range10V .. 30V
Consumption current: 
in standby mode, no more90uA
in alarm mode, no more20mA
Detector sensitivity0.05 dB/m .. 0.2 dB/m
Detector response time, no more5 sec.
Housing materialStainless steel

Selection table for additional resistors

FACP typeParallel connection (make)
LB-07Rd must ensure current consumption> 15 mA,
Rok \u003d 2 kOhm, VDok \u003d KD522.
RayRd = 2.4 kOhm, Rok = 2.4 kOhm, VDok = KD521A.
PPK-2Rd = 1.2 kOhm, Rok = 3.6 kOhm, VDok = KD521A.
fireballRd \u003d 1.5 kOhm (3.0 kOhm - to determine double drawdown),
Rok \u003d 4.7 kOhm, do not install VDok
Yakhont-16iRd \u003d 1.8 kOhm (4.0 kOhm - to determine double drawdown),
Rok = 8.2 kOhm, do not set VDok
WERSRd \u003d 820 Ohm (1.8 kOhm - to determine double drawdown),
Rok = 7.5 kOhm, do not set VDok

An example of the designation of the detector when ordering:

IPX 1X 2116.2Tryonx3x4x5x6
123456789
  1. IP - fire detector;
  2. Controlled fire factor:
    2 - smoke detector;
  3. Operating principle:
    12 - optoelectronic;
  4. The serial number of the development is 116.2;
  5. Name:
    Trion - the name of the detector;
  6. Execution:
    MK-OP - general industrial design;
  7. Presence of an address label*:
    no label (default) – no label;
    AM - the presence of an address label DPLS (address system "Orion");
  8. Body material:
    H - stainless steel;
  9. Type of cable entry*:
    K - for open cable laying with a diameter of 6.5-13.9 mm;
    TV1 / 2 (TV20) - for laying a cable with a diameter of 6.5-13.9 mm in a pipe with a connecting internal thread G1 / 2 (M20x1.5);
    ТН1/2 (ТН20) - for laying a cable with a diameter of 6.5-13.9 mm in a pipe with a connecting external thread G1/2 (M20x1.5);
    B - for laying with double sealing of an armored cable with an outer part with a diameter of 12.5-20.9 mm and an inner sheath diameter of 6.5-13.9 mm;
    KM10 - for laying a cable with a diameter of 3.1-8.6 mm in the RZTsH-10 metal hose;
    KM12 - for laying a cable with a diameter of 3.1-8.6 mm in the RZTsH-12 metal hose;
    KM15 - for laying a cable with a diameter of 6.1-11.7 mm in the RZTsH-15 metal hose;
    KM20 - for laying a cable with a diameter of 6.5-13.9 mm in the RZTsH-20 metal hose.
    * specified when ordering by the consumer.

DOWNLOAD ELECTRONIC PRODUCT CATALOGS *.PDF

Contacts

  • SMD Company LLC
  • 445009, Samarskay obl.,
  • Togliatty,
  • st. Novozavodskaya 2a, build. 309
  • Аккредитация URS ISO 9001
Write to us, we are online!